S-O
Seal and Groove Dimensions in Millimeters (mm) |
||||||||||||
Seal Height |
Seal Width |
Seal Diameter Range |
Sheet Thickness |
Seal & Groove Clearance |
Groove Height |
Groove Corner Radius |
Groove Width |
Spring Back Values (mm) |
Load Values N/mm circumference |
|||
SH |
SW |
SD |
ST |
SGS |
GH |
GR |
GW |
L |
T |
L |
T |
|
L |
T |
|||||||||||
00.79 (+/-0.05) |
0.70 |
6 - 30 |
0.13 |
0.18 |
0.10 |
0.65-0.70 |
0.25 |
1.00 |
0.04 |
0.03 |
30 |
50 |
01.19 (+/-0.05) |
0.95 |
10 - 45 |
0.13 |
0.20 |
0.15 |
0.95-1.00 |
0.30 |
1.40 |
0.05 |
0.04 |
20 |
25 |
01.57 (+/-0.05) |
1.25 |
12 - 220 |
0.15 |
0.25 |
0.15 |
1.25-1.35 |
0.35 |
1.90 |
0.08 |
0.06 |
10 |
40 |
02.39 (+/-0.05) |
1.90 |
30 - 220 |
0.25 |
0.38 |
0.25 |
1.90-2.00 |
0.50 |
2.70 |
0.10 |
0.08 |
35 |
65 |
03.18 (+/-0.08) |
2.55 |
45 - 380 |
0.38 |
0.51 |
0.30 |
2.55-2.65 |
0.75 |
3.45 |
0.15 |
0.13 |
45 |
100 |
03.96 (+/-0.08) |
3.20 |
80 - 600 |
0.41 |
0.61 |
0.41 |
3.20-3.30 |
1.25 |
4.40 |
0.20 |
0.17 |
40 |
110 |
04.78 (+/-0.10) |
3.80 |
100 - 750 |
0.51 |
0.76 |
0.46 |
3.85-4.00 |
1.25 |
5.10 |
0.22 |
0.18 |
65 |
150 |
06.35 (+/-0.10) |
5.10 |
250 - 1200 |
0.64 |
0.97 |
0.63 |
5.05-5.30 |
1.5 |
6.60 |
0.30 |
0.27 |
75 |
160 |
09.53 (+/-0.10) |
7.60 |
350 - 2000 |
0.97 |
1.27 |
0.79 |
7.60-8.00 |
1.5 |
9.65 |
0.40 |
0.32 |
120 |
250 |
12.70 (+/-0.13) |
10.20 |
650 - 3000 |
1.27 |
1.65 |
1.02 |
10.15-10.65 |
1.5 |
12.75 |
0.55 |
0.48 |
150 |
250 |
Note: Above given values are based on lab setup conditions especially the Load and Spring-Back values. Practically the values can differ based on the actual seal size, groove conditions, groove dimensions, surface finish and seal plating conditions.