T-O / T-DO / T-GO / T-SO
Seal and Groove Dimensions in Millimeters (mm) |
|||||||||||
Seal Height |
Seal Diameter Range |
Wall Thickness |
Seal & Groove Clearance |
Groove Height |
Groove Corner Radius |
Groove Width |
Spring Back Values (mm) |
Load Values N/mm circumference |
|||
SH |
SD |
ST |
SGS |
GH |
GR |
GW |
L |
T |
L |
T |
|
L |
T |
||||||||||
00.89 (+0.08/-0.03) |
8 - 30 |
0.15 |
- |
0.20 |
0.65-0.70 |
0.25 |
1.45 |
0.01 |
- |
115 |
- |
01.19 (+0.08/-0.03) |
10 - 45 |
0.20 |
- |
0.25 |
0.95-1.00 |
0.30 |
1.80 |
0.03 |
- |
105 |
- |
01.57 (+0.08/-0.03) |
12 - 220 |
0.25 |
0.36 |
0.30 |
1.15-1.25 |
0.35 |
2.30 |
0.03 |
0.03 |
125 |
155 |
02.39 (+0.08/-0.03) |
30 - 220 |
0.25 |
0.46 |
0.35 |
1.90-2.00 |
0.50 |
3.20 |
0.05 |
0.03 |
75 |
275 |
03.18 (+0.08/-0.03) |
45 - 380 |
0.25 |
0.51 |
0.45 |
2.55-2.65 |
0.75 |
4.05 |
0.07 |
0.04 |
45 |
205 |
03.96 (+0.10) |
80 - 600 |
0.41 |
0.51 |
0.60 |
3.20-3.30 |
1.25 |
5.10 |
0.10 |
0.08 |
95 |
175 |
04.78 (+0.13) |
100 - 750 |
0.51 |
0.64 |
0.70 |
3.85-4.00 |
1.25 |
6.35 |
0.10 |
0.08 |
105 |
175 |
06.35 (+0.13) |
250 - 1200 |
0.64 |
0.81 |
0.75 |
5.05-5.30 |
1.5 |
8.90 |
0.20 |
0.10 |
105 |
235 |
09.53 (+0.13) |
350 - 2000 |
0.97 |
1.24 |
1.00 |
8.25-8.50 |
1.5 |
12.70 |
0.15 |
0.12 |
175 |
305 |
12.70 (+0.15) |
650 - 3000 |
1.27 |
1.65 |
1.25 |
11.05-11.40 |
1.5 |
16.50 |
0.22 |
0.18 |
415 |
655 |
Note: Above given values are based on lab setup conditions especially the Load and Spring-Back values. Practically the values can differ based on the actual seal size, groove conditions; groove dimensions surface finish and seal plating conditions. Also do not refer the Load and Spring Back values for spring energized o-rings.